patriotnomad.blogg.se - Cisco asa 5505 software 8.4.6

CISCO ASA 5505 SOFTWARE 8.4.6 HOW TO
CISCO ASA 5505 SOFTWARE 8.4.6 PASSWORD

The diagram below illustrates the network topology for the configuration setup that we will describe. Let’s see the basic configuration setup of the most important steps that you need to configure. If you have a box on the same subnet as the cisco box, do an ipconfig /all and use the gateway listed there.That is, you can not configure the physical ports as Layer 3 ports, rather you have to create interface Vlans and assign the Layer 2 interfaces in each VLAN.īy default, interface Ethernet0/0 is assigned to VLAN 2 and its the outside interface (the one which connects to the Internet), and the other 7 interfaces (Ethernet0/1 to 0/7) are assigned by default to VLAN 1 and are used for connecting to the internal network. # In the Gateway IP field, type the gateway outside of your asa5505. # In the IP Address field, type: ‘0.0.0.0? # For the interface name, select ‘Outside’ (or whatever the outside interface is named) # Click ‘Routing’ on the left, Make sure ‘Static Routes’ is selected. Maybe it’s the static route, I do have a static route set, because I used the directions available here to give the unit a static IP: Peter, I’m not sure what problem you guys are having. Post navigation ← A Nice Note From My Supervisor Restoring Factory Defaults to the Cisco ASA 5505 Firewall via the ASDM → This entry was posted in Tech Support, Uncategorized on Jby curreri. To connect, double-click the connection entry you just created.Įnter your username and password, which we defined users on the Cisco ASA5505 device during the VPN Wizard. Password: put in your “Pre-shared Key” VPN (Connection password).Name: Put whatever you put for Tunnel Group Name (VPN Connection Username).On the Authentication Tab, make sure “Group Authentication” is selected.Host: The IP address or DNS name of the VPN Server.I used the same thing I put in for the Tunnel Group Name (VPN Connection Username), but you can use whatever you want.

Connection Entry: Name of the VPN connection.

To connect your new VPN, you’ll need the Cisco VPN Client.

Click “Schedule Reload,” Yes, and Exit ASDM.

Be sure to change the radio button at the top to Save the running configuration at the time of reload.

I like to do a reboot while I do this, and we can do it using the Cisco ASDM! Now that we’ve done all that, we should save it from working memory into the flash.

Change the IP address and Netmask to match that of your internal network, the subnet where your servers are located.

Double click the Entry under the Standard ACL tab.

Click the “Manage” button next to Split Tunnel Network List.

Click the Group Policy that corresponds to the one you defined during the Wizard, and click the Edit button.

Click “VPN” on the left side of the screen.

Click “Configuration” at the top of the screen.

One more step, without this you won’t be able to connect to anything besides the internal network when you are connected to the VPN.

Leave NAT Settings blank, but check “Enable Split tunneling” at the bottom and click Next.

IKE Policy defaults are fine, click Next.

Fill in DNS and WINS for your outside network and Click Next.

You can do whatever you want here, but here is my suggestion:

Click “New…” to create a new VPN IP pool.

CISCO ASA 5505 SOFTWARE 8.4.6 PASSWORD

Create a username and password for each VPN user, click Next.

Select “Authenticate using the local user database,” click Next.

Tunnel Group Name: Enter what I’m going to call your “VPN Connection Username,” and Click Next.

Select “Pre-shared key,” then fill in what I’m going to call your “VPN Connection Password.” This will be saved in the client and should be as long and secure as possible.Click the “Wizards” drop down, select “VPN Wizard.”.To configure the ASA5505, first log into it using the Cisco ASDM. The remote client doe not need to have an 5505 as a VPN endpoint, it only needs to have the Cisco VPN Client software installed.

CISCO ASA 5505 SOFTWARE 8.4.6 HOW TO

This walkthrough will describe how to use your Cisco ASA5505 as a VPN server for a remote client.